DA 213S is a seismic veneer anchor designed to meet performance criteria as defined by building codes. These anchors can be used for tieing brick veneer to wood stud, steel stud, steel framing, CMU masonry, brick and concrete. They are fabricated with shear lugs that accommodate 9 gauge veneer reinforcement. The connectors are individually mounted and are easily installed. The 14 gauge plate is engineered to be attached to the face of a CMU or concrete steel stud, wood stud or steel frame. The 12 gauge pintle shear lugs hold pencil rod in place for greater pull out stress resistance and ductility. Adjust 1-1/4" up or down for different course heights and allows at least 1/2" horizontal in-plane movement to accommodate expansion and contraction. A hot dipped galvanized finish is standard, and 304 stainless steel is available. It is recommended the use of two screws for stud applications, either the Stalgard or Stainless Steel SX Screws for steel stud, Stalgard Screws for wood stud, or a spike for concrete or masonry retrofit applications. Hot dipped galvanized conforms to ASTM A-153, Class B. Other gauge steel available on request.
Seismic Wire Pintle
The pintle is 3/16" diameter wire conforming to ASTM A-82 with a seismic clip welded to pintle. Pintle adjustments are maximum of 1-1/4" up or down. Continuous wire fits into place providing a single unit for stability. The seismic clip conforms to requirements of Uniform Building Codes for seismic zones. Continuous wire is embedded in mortar joint, secured to tie anchor which is fastened to support structure. It adds stability and protects against problems associated with thermal expansion and contraction. Also provides more uniform distribution of lateral forces. Hot dipped galvanized. Conforms to ASTM A-153, Class B.
Designed to be laid in the mortar joint of CMU masonry. Available in 3/16" wire conforming to ASTM A-82. A seismic wire pintle is connected to the seismic eye. Typically spaced 16" vertically and 16" horizontally. Continuous wire fits into the clip and is embedded into the mortar joint. Hot dipped galvanized conforming to ASTM A-153, Class B.
VIEW TECHNICAL DATASHEET
Seismic Strap Anchor
DA 431 is a special 14 gauge seismic corrugated veneer anchor with two shear lugs, which is engineered for use with pencil rod to resist out of plane movement and afford greater ductility in seismic zones 3 and 4. Designed to be screwed to wood or steel stud backup.
Seismic Dovetail Anchor
DA131 is a 16 gauge adjustable seismic corrugated veneer anchor with two shear lugs, which is engineered for use with pencil rod to resist out of plane movement and afford greater ductility in seismic zones 3 and 4. Engineered to fit standard dovetail slot with 5/8" throat opening.
|Dovetail Slot available, see page 83.|
|DA 167WT||16 ga. x 7"||500||55.0|
|DA 227WT||22 ga. x 7"||1,000||55.0|
|DA 227WT-T||22 ga. x 7"||1,000||55.0|
Stainless Steel is available with and without washers.This self-drilling screw has a hardened point for easy installation. Is frequently specified on stainless steel anchor jobs. The maximum in corrosion resistant.
|TEC 1012SS||#10 x 1-1/2"||1,000||17.0|
|TEC 10112SSW||#10 x 1-1/2" w/washer||1,000||20.0|
The maximum in corrosion resistant coating. Attractive silver-grey finish covers entire fastener surface. Compatible with painted or metal surfaces. Out performs existing mechanical and electro-platings. Does not promote corrosion that can be caused by electrochemical reaction between dissimilar metals.
|TEC 10112HC||#10 x 1-1/2"||3,000||34.0|
|TEC 10112HCW||#10 x 1-1/2" (w/washer)||2,500||30.0|
|TEC 102WW||#10 x 2" (w/washer)||2,000||30.0|
VIEW TECHNICAL DATASHEET
Primarily for use when there is no insulation and little potential for wallboard deterioration. DW-10HS is 6" long with 3-5/8" vertical adjustability. Stocked in 14 gauge Hot Dip Galvanized. 12 gauge and Type 304 Stainless Steel is available on a special order basis. All anchors furnished with 9/32" diameter holes.
Swage & mild pitch on legs of the Byna-Lok™ Wire Tie provide an integral track for continuous joint reinforcing wire. Suitable for standard 3/8" mortar joint. More surface engagement of the continuous wire and the integral track than any other system on the market. Reduces potential for incorrect placement or disengagement of the continuous wire due to workmanship error. Hassle-free installation of the continuous wire into the Byna-Lok™ Wire Tie. Economical; add continuous wire to masonry walls at little additional cost. Suitable for use with a variety of H&B anchors. Available 3/16" dia. x 3", 4", and 5" long, Hot Dip Galvanized finish. Type 304 Stainless Steel on a special order basis.
Vertical Expansion Joint: 3/8"x3"x50' with no adhesive; compression up to 35%; manufactured of closed cell neoprene conforming to ASTM D-1056, RE 41.