MASCO Catalog: Concrete Forming & Accessories

76 MASONS SUPPLY COMPANY Oregon (800) 537-3407 ♦ Washington (800) 537-6216 Clackamas | Eugene | West Eugene | Hillsboro | Medford | Portland | Salem | Ridgefield | Seattle | Tacoma | Woodinville M A S C O . N E T TIEING/HANDSET COIL THREAD Plate Washer For use with coil bolts, she bolts, taper ties and coil nuts. Washer sizes are designed to provide adequate bearing against wood form members. Maximum space between strongbacks should not exceed rod diameter plus 1/4". Battered Washer Battered washers are used with either coil bolts, she bolts and taper ties when the walers are at an angle to the tips.Permits any angle from 90° to 45°. SWL is based on maximum spacing of 3" between strongbacks. SPREADER CLIP FRICTION CLAMP BOLT WALER SHE-BOLT TIE No. Rod Diameter Wt (lbs) SY 31525 1-1/4" 3.0 No. Size Rod Diameter Wt (lbs) CFA PW331412 3" x 3" x 1/4" 1/2" 0.65 CFA PW331434 3" x 3" x 1/4" 3/4" 0.65 CFA PW441412 4" x 4" x 1/4" 1/2" 1.15 CFA PW441434 4" x 4" x 1/4" 3/4" 1.10 CFA PW443834 4" x 4" x 3/8" 3/4" 1.71 CFA PW553834 5" x 5" x 3/8" 3/4" 2.66 CFA PW661234 6'" x 6" x 1/2" 3/4" 5.10 CFA PW55121 5" x 5" x 1/2" 1" 3.55 CFA PW66121 6" x 6" x 1/2" 1" 5.10 CFA PW6634114 6" x 6" x 3/4" 1-1/4" 8.45 CFA PW6610112 6" x 6" x 1" 1-1/2" 10.00 Other sizes available on request. No. Rod Diameter Wt (lbs) SY 31626 1-1/4" 3.5 SY 31627 1-1/2" 6.0 SWL provides a factor of safety of approximately 2 to 1. COIL BOLT COIL TIE WASHER BATTER WASHER Wale Bolt Assembly This Wale Bolt Assembly consists of 1/2″ “L” bolt, a round cut washer, a Flat Washer and two 1/2″ Coil Nuts. The assembly is used to fasten wales to crane-handled gang forms. One size assembly will secure wales up to 10″ thick. The bolt has 8″ of coil thread on the long end and 1-1/2″ of coil thread on the short end. The short end of the bolt is inserted through a 9/16″ hole drilled through the center of the stud. The cut washer and 1/2″ nut fastens the bolt to the stud. The long end of the bolt extends between the wales and allows the wales to be drawn tightly against the stud using a flat washer and the second 1/2″ nut. Wale Bolt assemblies are normally spaced at four feet intervals along the wales. The safe working load of the assembly is dependent on the wale members being used. No. Wt (lbs) DS B14W 1.74 6-10 62 Medium/Heavy Formwork B-14-WWale Bolt Assembly Dayton Superior B-14-W Wale Bolt Assembly consists of a 1/2" “L” bolt, a round cut washer, a B-11 Flat Washer and two 1/2" B-13 Coil Nuts. The B-14-W assembly is used to fasten wales to crane-handled gang forms. One size assembly will secure wales up to 10" thick. The bolt has 8" of coil thread on the long end and 1-1/2" of coil thread on the short end. The short end of the bolt is inserted through a 9/16" hole drilled through the center of the stud. The cut washer and 1/2" nut fastens the bolt to the stud. The long end of the bolt extends between the wales and allows the wales to be drawn tightly against the stud using a flat washer and the second 1/2" nut. Wale Bolt Assemblies are normally spaced at four feet intervals along the wales. The safe working load of the assembly is dependent on the wale members being used. B-15 Plastic Cone Removal Wrench Dayton Superior B-15 Plastic Cone Removal Wrench is designed to remove the plastic cones from Screw-On Coil Ties. Available for 1/2", 3/4", 1" and 1-1/4" diameter cones. B-16 Coil Loop Insert Straight Dayton Superior B-16 Coil Loop Insert Straight is made of a single looped wire strut welded to a helix coil. B-16 inserts are available in 1/2", 3/4" and 1" nominal diameter standard or screw-on coil and in various standard lengths. The B-16 is also available in other than standard lengths and with a nailing washer face on special order. 12" 3" 1 1/2" 8" Coil Thread Washer B-16 Coil Loop Insert B-13 Coil Nut 1/2" “L” Bolt To Order: Specify: (1) quantity, (2) name. Example: 300 pcs. B-14-W Wale Bolt Assembly, complete with nuts and washers. B-16 Coil Loop Insert B-14-WWale Bolt Assembly B-15 Plastic Cone Removal Wrench B-16 Coil Loop Insert, Straight Selection Chart Safe Working Minimum Bolt Insert Wire Strut Load Tension Concrete Diameter Length Diameter (lbs.) Strength (psi) 1/2" 3" .223 4,500 2,000 1/2" 4" .223 4,500 2,000 1/2" 6" .306 7,500 2,000 3/4" 4" .223 4,500 2,000 3/4" 6" .306 7,500 2,000 1" 6" .306 7,500 2,000 1" 8" .306 7,500 SWL provides a factor of safety of approximately 2 to 1. SWL may vary wi h concrete weight and strength, as well as with insert setback and edge distance. Contact the Dayton Superior Technical Service Department for variables. To Order: Specify: (1) quantity, (2) name, (3) diameter, (4) insert length Medium/Heavy Forming Products 6-10 62 Medium/He vy Formwork B-14-WWale B lt Assembly Dayton Superior B-14-W Wale Bolt Assembly consists of a 1/2" “L” bolt, a round cut washer, a B-11 Flat Washer and two 1/2" B-13 Coil Nuts. The B-14-W assembly is used to fast n wales to crane-handled gang forms. One size assembly will secure wales up to 10" thick. The bolt has 8" of coil thread on the long end and 1-1/2" of coil thread on the short end. The short end of the bolt is inserted through a 9/16" hole drilled through the center of the stud. The cut washer and 1/2" nut fastens the bolt to the stud. The long end of the bolt extends between the wales and allows th wales to be draw tightly gainst the stud using a fl t washe and the second 1/2" nut. Wale Bolt Assemblies are normally spaced at four feet intervals along the wales. The safe working load of the assembly is dependent on the wale members being used. B-15 Pl stic Cone Removal Wrench Dayton Superior B-15 Plastic Cone Removal Wrench is designed to remove the plastic cones from Screw-On Coil Ties. Available for 1/2", 3/4", 1" and 1-1/4" diameter cones. B-16 Coil Loop Insert Straight Dayton Superior B-16 Coil Loop Insert Straight is made of a single looped wire strut welded to a helix coil. B-16 inserts are available in 1/2", 3/4" and 1" nominal diameter standard or screw-on coil and in various standard lengths. The B-16 is also available in other than standard lengths and with a nailing washer face on special order. 12" 3" 1 1/2" 8" Coil Thread Washer B-16 Coil Loop Insert B-13 Coil Nut 1/2" “L” Bolt To Order: Specify: (1) quantity, (2) name. Example: 300 pcs. B-14-W Wale Bolt Assembly, complete with nuts and washers. B-16 Coil Loop Insert B-14-WWale Bolt Assembly B-15 Plastic Cone Removal Wrench B-16 Coil Loop Insert, Straight Selection Chart Safe Working Minimum Bolt Insert Wire Strut Load Tension Concrete Diameter Length Diameter (lbs.) Strength (psi) 1/2" 3" .223 4,500 2,000 1/2" 4" .223 4,500 2,000 1/2" 6" .306 7,500 2,000 3/4" 4" .223 4,500 2,000 3/4" 6" .306 7,500 2,000 1" 6" .306 7,500 2,000 1" 8" .306 7,500 SWL provides a factor of safety of approximately 2 to 1. SWL may vary with concrete weight and strength, as well as with insert setback and edge distance. Contact the Dayton Superior Technical Service Department for variables. To Order: Specify: (1) quantity, (2) name, (3) diameter, (4) insert length Medium/Heavy Forming Products Cast Bearing Washer Cast Bearing Washers are used with she bolts or taper ties with steel, aluminu or ood form . SWL based on maximum spacing of 3" between strongbacks. SWL 25,000 lbs.