101 322
101
MASONS SUPPLY COMPANY
Oregon (800) 537-3407 ♦ Washington (800) 537-6216
Clackamas | Eugene | West Eugene | Hillsboro | Medford | Portland | Salem | Wilsonville | Ridgefield | Seattle | Tacoma | Woodinville
M A S C O . N E T
Plate Washer
For use with coil bolts, she bolts, taper ties and coil nuts.
Washer sizes are designed to provide adequate bearing
against wood form members. Maximum space between
strongbacks should not exceed rod diameter plus 1/4".
Battered Washer
Battered washers are used with either coil bolts, she bolts
and taper ties when the walers are at an angle to the
tips.Permits any angle from 90° to 45°. SWL is based on
maximum spacing of 3" between strongbacks.
SPREADER
CLIP
FRICTION CLAMP BOLT
WALER
SHE-BOLT
TIE
No.
Rod Diameter
Wt (lbs)
SY 31525
1-1/4"
3.0
No.
Size
Rod Diameter
Wt (lbs)
CFA PW331412 3" x 3" x 1/4"
1/2"
0.65
CFA PW331434 3" x 3" x 1/4"
3/4"
0.65
CFA PW441412 4" x 4" x 1/4"
1/2"
1.15
CFA PW441434 4" x 4" x 1/4"
3/4"
1.10
CFA PW443834 4" x 4" x 3/8"
3/4"
1.71
CFA PW553834 5" x 5" x 3/8"
3/4"
2.66
CFA PW661234 6'" x 6" x 1/2"
3/4"
5.10
CFA PW55121
5" x 5" x 1/2"
1"
3.55
CFA PW66121
6" x 6" x 1/2"
1"
5.10
CFA PW6634114 6" x 6" x 3/4"
1-1/4"
8.45
CFA PW6610112 6" x 6" x 1"
1-1/2"
10.00
Other sizes available on request.
No.
Rod Diameter
Wt (lbs)
SY 31626
1-1/4"
3.5
SY 31627
1-1/2"
6.0
SWL provides a factor of safety of approximately 2 to 1.
COIL BOLT
COIL TIE
WASHER
BATTER
WASHER
Wale Bolt Assembly
This Wale Bolt Assembly consists of 1/2″ “L” bolt, a round cut washer, a Flat Washer and
two 1/2″ Coil Nuts. The assembly is used to fasten wales to crane-handled gang forms.
One size assembly will secure wales up to 10″ thick. The bolt has 8″ of coil thread on the
long end and 1-1/2″ of coil thread on the short end.
The short end of the bolt is inserted through a 9/16″ hole drilled through the center of
the stud. The cut washer and 1/2″ nut fastens the bolt to the stud. The long end of the
bolt extends between the wales and allows the wales to be drawn tightly against the
stud using a flat washer and the second 1/2″ nut. Wale Bolt assemblies are normally
spaced at four feet intervals along the wales. The safe working load of the assembly is
dependent on the wale members being used.
No.
Wt (lbs)
DS B14W 1.74
62
Medium/Heavy
Formwork
B-14-WWale Bolt Assembly
Dayton Superior B-14-W Wale Bolt Assembly consists of a 1/2" “L” bolt,
a round cut washer, a B-11 Flat Washer and two 1/2" B-13 Coil Nuts. The
B-14-W assembly is used to fasten wales to crane-handled gang forms.
One size assembly will secure wales up to 10" thick. The bolt has 8" of coil
thread on the long end and 1-1/2" of coil thread on the short end.
The short end of the bolt is inserted through a 9/16" hole drilled through
the center of the stud. The cut washer and 1/2" nut fastens the bolt to
the stud. The long end of the bolt extends between the wales and allows
the wales to be drawn tightly against the stud using a flat washer and the
second 1/2" nut.
Wale Bolt Assemblies are normally spaced at four feet intervals along
the wales. The safe working load of the assembly is dependent on the wale
members being used.
B-15 Plastic Cone Removal Wrench
Dayton Superior B-15 Plastic Cone Removal Wrench is designed to
remove the plastic cones from Screw-On Coil Ties. Available for 1/2", 3/4",
1" and 1-1/4" diameter cones.
B-16 Coil Loop Insert Straight
Dayton Superior B-16 Coil Loop Insert Straight is made of a single looped wire strut welded to a helix coil. B-1
are available in 1/2", 3/4" and 1" nominal diameter standard or screw-on coil and in various standard lengths. The
also available in other than standard lengths and with a nailing washer face on special order.
12"
3"
1 1/2"
8" Coil Thread
Washer
B-16 Coil
Loop Insert
1/2" “L” Bolt
To Order:
Specify: (1) quantity, (2) na
Example:
300 pcs. B-14-W Wale Bolt
complete with nuts and wa
B-16 Coil Loop Insert
B-14-WWale
Bolt Assembly
B-15 Plastic Cone
Removal Wrench
B-16 Coil Loop Insert, Straight Selection Chart
Safe Working
Minimum
Bolt
Insert
Wire Strut
Load Tension
Concrete
Diameter
Length
Diameter
(lbs.)
Strength (psi)
1/2"
3"
.223
4,500
2,000
1/2"
4"
.223
4,500
2,000
1/2"
6"
.306
7,500
2,000
3/4"
4"
.223
4,500
2,000
3/4"
6"
.306
7,500
2,000
1"
6"
.306
7,500
2,000
1"
8"
.306
7,500
SWL provides a factor of safety of approximately 2 to 1.
SWL may vary with concrete weight and strength, as well as with insert setback and edge
distance. Contact the Dayton Superior Technical Service Department for variables.
To Order:
Specify:
(1) quant
(2) name
(3) diam
(4) insert
Medium/Heavy Forming Products
6-10
62
Medium/He vy
Formwork
B-14-WWale B lt Assembly
Dayton Superior B-14-W Wale Bolt Assembly consists of a 1/2" “L” bolt,
a round cut washer, a B-11 Flat Washer and two 1/2" B-13 Coil Nuts. The
B-14-W assembly is used to fast n wales to crane-handled gang forms.
One size assembly will secure wales up to 10" thick. The bolt has 8" of coil
thread on the long end and 1-1/2" of coil thread on the short end.
The short end of the bolt is inserted through a 9/16" hole drilled through
the center of the stud. The cut washer and 1/2" nut fastens the bolt to
the stud. The long end of the bolt extends between the wales and allows
th wales to be draw tightly gainst the stud using a fl t washe and the
second 1/2" nut.
Wale Bolt Assemblies are normally spaced at four feet intervals along
the wales. The safe working load of the assembly is dependent on the wale
members being used.
B-15 Pl stic Cone Removal Wrench
Dayton Superior B-15 Plastic Cone Removal Wrench is designed to
remove the plastic cones from Screw-On Coil Ties. Available for 1/2", 3/4",
1" and 1-1/4" diameter cones.
B-16 Coil Loop Insert Straight
Dayton Superior B-16 Coil Loop Insert Straight is made of a single looped wire strut welded to a helix coil. B-16 inserts
are available in 1/2", 3/4" and 1" nominal diameter standard or screw-on coil and in various standard lengths. The B-16 is
also available in other than standard lengths and with a nailing washer face on special order.
12"
3"
1 1/2"
8" Coil Thread
Washer
B-16 Coil
Loop Insert
B-13
Coil Nut
1/2" “L” Bolt
To Order:
Specify: (1) quantity, (2) name.
Example:
300 pcs. B-14-W Wale Bolt Assembly,
complete with nuts and washers.
B-16 Coil Loop Insert
B-14-WWale
Bolt Assembly
B-15 Plastic Cone
Removal Wrench
B-16 Coil Loop Insert, Straight Selection Chart
Safe Working
Minimum
Bolt
Insert
Wire Strut
Load Tension
Concrete
Diameter
Length
Diameter
(lbs.)
Strength (psi)
1/2"
3"
.223
4,500
2,000
1/2"
4"
.223
4,500
2,000
1/2"
6"
.306
7,500
2,000
3/4"
4"
.223
4,500
2,000
3/4"
6"
.306
7,500
2,000
1"
6"
.306
7,500
2,000
1"
8"
.306
7,500
SWL provides a factor of safety of approximately 2 to 1.
SWL may vary with concrete weight and strength, as well as with insert setback and edge
distance. Contact the Dayton Superior Technical Service Department for variables.
To Order:
Specify:
(1) quantity,
(2) name,
(3) diameter,
(4) insert length
Medium/Heavy Forming Products
Cast Bearing Washer
Cast Bearing Washers are used with she bolts or
taper ties with steel, aluminu or ood form .
SWL based on maximum spacing of 3" between
strongbacks. SWL 25,000 lbs.
COIL THREAD
TIEING/HANDSET